Home page Home page Hobbies & Garden Tools Soldering Irons & Accessories QRP Pixie Kit for Soldering CW Transmitter and Receiver for the 40 m Band 7.023–7.026 MHz Power Supply 9–14 V BNC Connector for Radio Amateurs
QRP Pixie Kit for Soldering CW Transmitter and Receiver for the 40 m Band 7.023–7.026 MHz Power Supply 9–14 V BNC Connector for Radio Amateurs

QRP Pixie Kit for Soldering CW Transmitter and Receiver for the 40 m Band 7.023–7.026 MHz Power Supply 9–14 V BNC Connector for Radio Amateurs

Soldering kit for a simple telegraph transceiver Pixie V5.1. Printed circuit board and components for building a small QRP station for shortwave. Full description
In stock
€8.25
Price incl. VATImport charges will apply
Safe shopping Safe shopping
Overview
QRP Pixie Kit for Soldering CW Transmitter and Receiver for the 40 m Band 7.023–7.026 MHz Power Supply 9–14 V BNC Connector for Radio Amateurs

The QRP Pixie kit is a soldering kit from which you can build a simple shortwave station for telegraph operation. The finished device operates as both a transmitter and receiver in the amateur radio 40 m band at a frequency of 7.023–7.026 MHz, determined by the included crystal. The circuit is designed for CW operation, meaning it transmits Morse code using a telegraph key. The station falls into the QRP category, which denotes low-power devices, popular among radio amateurs for their simplicity and low power consumption. It is powered by a direct current voltage of 9–14 V via a power adapter connector.

The kit includes a green printed circuit board marked V5.1 with printed component positions, making it clear where each component belongs during assembly. The board has designated spaces for two 3.5 mm connectors labelled PHONE and KEY, into which you connect headphones and the telegraph key. The antenna connects via a BNC connector, which is also included in the package. The integrated circuit is inserted into an eight-pin socket, preventing overheating during soldering and allowing for easy replacement if needed.

  • Type – shortwave CW transmitter and receiver QRP Pixie kit
  • Band – 40 m
  • Frequency – 7.023–7.026 MHz
  • Mode of Operation – CW telegraphy
  • Power Supply – DC 9–14 V
  • Operating Temperature – −5 to 50 °C
  • Board Version – V5.1
  • Connectors – BNC for antenna, power connector and two 3.5 mm connectors for headphones and key
  • Design – soldering kit
  • Package Contents – V5.1 printed circuit board, crystal, integrated circuit with eight-pin socket, two transistors, resistors, ceramic and electrolytic capacitors, inductors, two diodes, trimmer, power connector, two 3.5 mm connectors with nuts and BNC connector

When assembling, start with the lowest components, that is, the resistors, diodes and inductors, followed by the capacitors and transistors, and finally the connectors and socket. Pay attention to the correct polarity of the electrolytic capacitors and diodes and the orientation of the transistors according to the printed circuit board markings. You will need a soldering iron with a fine tip, solder, and wire cutters. Once completed, connect the antenna for the 40 m band, headphones, telegraph key and a suitable power supply. The antenna, headphones, key, and power adapter are not included in the package.

The Pixie kit is a classic project that many radio amateurs and enthusiasts of high-frequency technology start with. The small number of components makes it a suitable kit for practising soldering as well as understanding the principles of a simple transmitter and receiver. The finished station allows you to try telegraph operation with low power in the 40 m band. The kit is suitable for electronics clubs, amateur radio clubs, and individual hobbyists. Thanks to the eight-pin socket and clear markings on the board, you can complete the build even without extensive experience.

Price incl. VAT €8.25