Home page Home page Home & Household Supplies Home electrical supplies Back boxes and blanking plates Lever Wire Connectors 10 pcs Quick Connector 1 Input and 4 Outputs for 0.08 to 2.5 mm² Conductors 32 A 250 V Copper Contacts Screwless
Lever Wire Connectors 10 pcs Quick Connector 1 Input and 4 Outputs for 0.08 to 2.5 mm² Conductors 32 A 250 V Copper Contacts Screwless

Lever Wire Connectors 10 pcs Quick Connector 1 Input and 4 Outputs for 0.08 to 2.5 mm² Conductors 32 A 250 V Copper Contacts Screwless

Lever wire connectors for distributing one conductor to four without soldering. Copper contacts and a stainless steel spring hold each conductor firmly in place. Full description
In stock
€14.37
Price incl. VATImport charges will apply
Safe shopping Safe shopping
Overview
Lever Wire Connectors 10 pcs Quick Connector 1 Input and 4 Outputs for 0.08 to 2.5 mm² Conductors 32 A 250 V Copper Contacts Screwless

The pack contains ten lever wire connectors for distributing one conductor to four outputs. The incoming conductor is inserted from one side and the four outgoing conductors from the opposite side, with each secured by its own lever. The connection can be disconnected at any time without damaging the conductor. The connectors are rated for a nominal current of 32 A and a nominal voltage of 250 V. They are therefore suitable for lighting circuits, socket circuits and wiring small appliances. Installation requires no soldering, screwing or insulating tape.

Inside the connector are contacts made from red copper, offering good conductivity and corrosion resistance. A flexible stainless steel clip presses the conductors into place, keeping the connection secure even after the levers have been opened repeatedly. The housing is made from flame-retardant plastic with increased resistance to high temperatures. The connector accepts conductors with a cross-sectional area of 0.08 to 2.5 mm², including solid single-core conductors and flexible stranded wires.

The branching design takes the place of bulkier terminal blocks and joining several conductors under one screw. Each conductor has its own opening and lever, so you can disconnect one output without affecting the others. The connector is suitable for connecting four lights to one switch, distributing a neutral or protective conductor in several directions, or adding more appliances to an existing circuit. There is a small eyelet with a hole on the side of the housing.

  • Type – lever wire connector with one input and four outputs
  • Nominal current – 32 A
  • Nominal voltage – 250 V
  • Conductor cross-section – 0.08 to 2.5 mm²
  • Dimensions – 29.5 x 23 x 13.3 mm
  • Contacts – red copper
  • Spring – stainless steel
  • Housing – flame-retardant plastic with increased heat resistance
  • Operation – a separate lever for each of the five conductors
  • Pack contents – 10 lever wire connectors with 1 input and 4 outputs

Even a less experienced DIY enthusiast can install the connectors. First, strip the insulation from the end of the conductor, then lift the lever and insert the stripped end into the opening as far as it will go. Finally, fold the lever back down to secure the conductor. Connect all four output conductors in the same way. To disconnect the connection, simply lift the lever again and pull out the conductor. Always disconnect the power supply before working on electrical wiring, and make sure that no bare conductor protrudes from the connector housing.

The pack of ten is ideal for smaller electrical installation jobs in a flat, garage or holiday home. You can distribute one supply in four directions without tools or an additional terminal block. The red copper contacts ensure a reliable connection without tools, and the connectors can be reused. The compact housing, measuring 29.5 x 23 x 13.3 mm, also fits in a smaller junction box. A practical solution for electricians, maintenance workers and experienced DIY enthusiasts.

Price incl. VAT €14.37