Home page Home page PC & Laptop Accessories PC Components CPU coolers and fans Fan 40 x 40 x 10 mm 5 V 2-pin Quiet 20 dBA 6000 rpm Oil-Lubricated Bearing Black For CPU 3D Printer and Electronics Enclosure Cooling
Fan 40 x 40 x 10 mm 5 V 2-pin Quiet 20 dBA 6000 rpm Oil-Lubricated Bearing Black For CPU 3D Printer and Electronics Enclosure Cooling

Fan 40 x 40 x 10 mm 5 V 2-pin Quiet 20 dBA 6000 rpm Oil-Lubricated Bearing Black For CPU 3D Printer and Electronics Enclosure Cooling

Small quiet 40 mm 5 V cooling fan with a two-wire cable for dissipating heat from processors, 3D printer boards and compact electronics enclosures. Full description
In stock
€8.25
Price incl. VATImport charges will apply
Safe shopping Safe shopping
Overview
Fan 40 x 40 x 10 mm 5 V 2-pin Quiet 20 dBA 6000 rpm Oil-Lubricated Bearing Black For CPU 3D Printer and Electronics Enclosure Cooling

The compact 40 x 40 x 10 mm fan is designed for places where space is limited but reliable heat dissipation is still needed. It operates on a 5 V power supply and connects via a two-wire cable with a small 2-pin connector. It is suitable for a computer case, a small CPU heatsink, an electronics enclosure or a 3D printer head. The black plastic frame has four mounting holes in the corners, so you can easily screw the fan onto a grille, heatsink or panel. Its slim profile takes up very little space in your setup.

The rotor spins at 6000 rpm with a tolerance of 10%, and the fan delivers an airflow of 5.5 CFM, which is sufficient for cooling small components, voltage regulators and chips for a fan of this size. The noise level is specified at 20 dBA, so the fan is not disruptive during normal operation. It draws just 0.12 A, so it does not put unnecessary strain on the power supply or control board. The oil-lubricated bearing ensures smooth operation, and the manufacturer specifies a service life of 20,000 hours.

  • Dimensions – 40 x 40 x 10 mm
  • Mounting hole spacing – 32 mm
  • Power supply – 5 V
  • Current – 0.12 A
  • Speed – 6000 rpm ± 10%
  • Airflow – 5.5 CFM
  • Noise level – 20 dBA
  • Bearing – oil-lubricated
  • Service life – 20,000 h
  • Connection – 2 wires and a 2-pin connector with 2.5 mm pitch
  • Colour – black
  • Package contents – 1 fan measuring 40 x 40 x 10 mm with attached cable and connector

When installing the fan, pay attention to the direction of airflow; the intake and exhaust sides are marked on the frame. Connect the fan to a 5 V power supply or output, and route the cable so that it does not touch the blades. From time to time, it is advisable to remove accumulated dust from the blades and frame using a soft brush or compressed air; the fan will then run more quietly and cool more effectively. The 32 mm hole spacing matches standard mounts and grilles for 40 mm fans, so replacing an old part usually requires no modifications. If you want to increase airflow, you can use several units side by side in one setup, each connected to its own 5 V output. The fan can be positioned horizontally or vertically, as required by the device.

This small 40 mm fan is a practical replacement part and an accessory for custom projects where air needs to be moved into or out of a confined space. It is suitable for use in computers, 3D printers, network equipment and home electronics. Its low current draw, quiet operation and simple two-wire connection make it a versatile component for the workshop. Thanks to its thickness of just 10 mm, it also fits into very narrow enclosures.

Price incl. VAT €8.25