Home page Home page Hobbies & Garden Tools Soldering Irons & Accessories S-Pixie Kit for Soldering QRP CW Transceiver 7.023 MHz for 40 m Band Power 1.2 W Power Supply 9–13.8 V Transparent Acrylic Case
S-Pixie Kit for Soldering QRP CW Transceiver 7.023 MHz for 40 m Band Power 1.2 W Power Supply 9–13.8 V Transparent Acrylic Case

S-Pixie Kit for Soldering QRP CW Transceiver 7.023 MHz for 40 m Band Power 1.2 W Power Supply 9–13.8 V Transparent Acrylic Case

Soldering kit for a small telegraph station S-Pixie with a board, components, and an acrylic case. It transmits and receives on short waves for radio amateurs. Full description
In stock
€14.80
Price incl. VATImport charges will apply
Safe shopping Safe shopping
Overview
S-Pixie Kit for Soldering QRP CW Transceiver 7.023 MHz for 40 m Band Power 1.2 W Power Supply 9–13.8 V Transparent Acrylic Case

The S-Pixie kit is a soldering kit from which you can assemble a small shortwave station for telegraph operation. The finished device functions as both a transmitter and a receiver and operates at a frequency of 7.023 MHz in the amateur radio 40 m band. It is designed for CW operation, meaning it transmits Morse code using manual keying. The output power reaches 1.2 W, placing the station in the QRP category, as radio amateurs refer to low-power devices. The kit also includes a transparent acrylic case in which to store the completed board.

The device is powered by a direct current voltage of 9–13.8 V, and the power supply should provide at least 500 mA. The seller recommends powering it from batteries, which can be used away from home. During reception, the idle current is around 20 mA, so the station will last a long time on batteries. The antenna connects via a BNC connector and should have an impedance of 50 Ω and a standing wave ratio of less than 2.0.

  • Type – S-Pixie shortwave CW transceiver kit
  • Frequency – 7.023 MHz
  • Band – 40 m
  • Mode of Operation – CW with manual keying
  • Output Power – 1.2 W
  • Power Supply – DC 9–13.8 V, power supply at least 500 mA
  • Current Consumption during Reception – approximately 20 mA
  • Antenna – 50 Ω, 7 MHz, SWR below 2.0
  • Case – transparent acrylic
  • Design – soldering kit
  • Contents of the Package – printed circuit board, parts of the acrylic case, plastic spacers, and a set of electronic components for soldering including a crystal, integrated circuit with socket, potentiometer, BNC connector, 3.5 mm connectors, and power connector

When assembling, install components from the lowest to the highest, starting with resistors and diodes, followed by capacitors and transistors, and finishing with connectors, the potentiometer, and the integrated circuit socket. Pay attention to the polarity of electrolytic capacitors and diodes, and ensure the correct orientation of transistors according to the board printing. You will need a soldering iron with a fine tip, solder, wire cutters, and a well-lit workspace. Before assembling the case parts, remove the protective film, then place the board on the spacers and assemble the case according to the shape of the individual parts. The antenna, telegraph key, headphones, and power supply are not included in the package.

The S-Pixie kit is a popular project for both novice and advanced radio amateurs who want to try building their own station. The small number of components and the circuit diagram make it an understandable kit for grasping the principles of a simple transmitter and receiver. The finished station in the acrylic case looks neat, and the board is protected from dust and accidental contact. The kit is suitable for electronics clubs, amateur radio clubs, and independent hobbyists. With a power supply of 9–13.8 V, it can easily be operated from batteries both at home and outdoors.

Price incl. VAT €14.80