Home page Home page Hobbies & Garden Tools Soldering Irons & Accessories FM Radio Kit for Soldering RDA5807M with Acrylic Case 158 x 74 x 28 mm 87.5–108 MHz USB-C Power and 2x AA for Education
FM Radio Kit for Soldering RDA5807M with Acrylic Case 158 x 74 x 28 mm 87.5–108 MHz USB-C Power and 2x AA for Education

FM Radio Kit for Soldering RDA5807M with Acrylic Case 158 x 74 x 28 mm 87.5–108 MHz USB-C Power and 2x AA for Education

Complete soldering kit for an FM receiver with an acrylic cover, display, 3 W speaker, and 30 cm antenna. A functional radio as an educational project for schools. Full description
In stock
€44.93
Price incl. VATImport charges will apply
Safe shopping Safe shopping
Overview
FM Radio Kit for Soldering RDA5807M with Acrylic Case 158 x 74 x 28 mm 87.5–108 MHz USB-C Power and 2x AA for Education

This FM radio kit for soldering contains everything needed to assemble a complete receiver, including a transparent acrylic case. Once completed, the radio will measure 158 x 74 x 28 mm, allowing for clear visibility of the entire populated board. The RDA5807M module, which has high sensitivity and low noise, is responsible for receiving stations and tunes into the FM band 87.5–108 MHz. The frequency is displayed on a four-digit LED display, and the buttons on the front are used for tuning and volume adjustment. The components are supplied separately, so assembly requires manual soldering.

The electronics are controlled by the STC15W408AS microcontroller, with sound powered by the AXS2031 digital amplifier delivering up to 5 W, and sound reproduction is handled by a 4 Ω speaker rated at 3 W. The 3.3 V buck-boost power module maintains a stable voltage even with input drops down to 2.5 V, ensuring that the display and microcontroller operate reliably even with partially depleted batteries. The radio can be powered via a USB-C connector from a 5 V source, or from two AA batteries that fit into a compartment inside the case. Both power sources cannot be connected simultaneously; always use only one of them.

  • Radio Module – RDA5807M
  • Reception Band – FM 87.5–108 MHz
  • Control Chip – STC15W408AS Microcontroller
  • Amplifier – AXS2031 up to 5 W mono
  • Speaker – 3 W with 4 Ω impedance
  • Display – Four-digit LED display
  • Antenna – Rotatable telescopic 30 cm
  • Power Supply – USB-C 5 V or 2x AA 3 V
  • Connectors – USB-C and 3.5 mm audio output
  • Controls – Switch and buttons for tuning and volume
  • Dimensions with Case – 158 x 74 x 28 mm
  • Board Dimensions – 100 x 59 mm
  • Package Contents – PCB, RDA5807M module, 3.3 V power module, microcontroller with socket, LED display, speaker, telescopic antenna, USB-C cable, holder for 2 AA batteries, resistors, capacitors, transistors, buttons, 3.5 mm connector, trimmer, wires, acrylic case parts, screws, and spacers

When building, first check the components against the list and then solder from the lowest parts to the highest. Secure the antenna with an M3 screw and solder it from the back of the board. Finally, connect the speaker wires and battery holder, attach the board with double-sided tape, screw in the spacers, and assemble the acrylic panels of the case. To clean the cover, simply use a dry or slightly damp cloth.

The kit with the case is an ideal choice for anyone who wants to have a finished and good-looking radio after completing the soldering. The transparent cover protects the populated board while also showing how the device works inside. The telescopic antenna, measuring 30 cm, improves reception, and the dual power supply allows for operation at home and on the go. The kit is suitable for pupils, students of technical fields, electronics clubs, and hobbyists. It is a practical way to learn soldering while also building a useful device.

Price incl. VAT €44.93