Home page Home page Hobbies & Garden Tools Soldering Irons & Accessories FM Radio Construction Kit for Soldering RDA5807M 87.5–108 MHz LED Display Amplifier 5 W Power Supply USB-C and 2x AA Without Box For Education
FM Radio Construction Kit for Soldering RDA5807M 87.5–108 MHz LED Display Amplifier 5 W Power Supply USB-C and 2x AA Without Box For Education

FM Radio Construction Kit for Soldering RDA5807M 87.5–108 MHz LED Display Amplifier 5 W Power Supply USB-C and 2x AA Without Box For Education

Soldering kit for FM receiver with blue board 100 x 59 mm, 30 cm telescopic antenna and 3 W speaker. Suitable project for practicing soldering at school. Full description
In stock
€37.07
Price incl. VATImport charges will apply
Safe shopping Safe shopping
Overview
FM Radio Construction Kit for Soldering RDA5807M 87.5–108 MHz LED Display Amplifier 5 W Power Supply USB-C and 2x AA Without Box For Education

The FM radio construction kit for soldering is a practical electronic project that allows you to build a functioning radio broadcast receiver. The heart of the kit is the high-quality module RDA5807M, which offers high sensitivity, low noise, and good resistance to interference. The radio receives stations in the range of 87.5–108 MHz, covering common FM broadcasts. The tuned frequency is displayed on a four-digit LED display, and control is provided by buttons for changing frequency and volume. The kit comes as individual parts and requires manual soldering and assembly.

Control is managed by the microcontroller STC15W408AS, and sound is amplified by the digital amplifier AXS2031 with an output power of 5 W in mono mode. It maintains clear sound without distortion even at around 2.5 V. Power is stabilised by a 3.3 V buck-boost module, which maintains the correct voltage for the microcontroller and display within an input voltage range of 2.5 to 5.5 V. The radio can be powered either via the USB-C connector from a 5 V source or from two AA batteries. Both power supply methods cannot be used simultaneously; always choose only one. This version of the kit is supplied without a box, so the finished board remains clearly visible.

  • Radio Module – RDA5807M
  • Frequency Range – FM 87.5–108 MHz
  • Microcontroller – STC15W408AS
  • Amplifier – AXS2031 with 5 W mono output
  • Speaker – 4 Ω and 3 W
  • Display – four-digit LED
  • Antenna – telescopic 30 cm long
  • Power Supply – USB-C 5 V or 2 AA batteries 3 V
  • Control – buttons for frequency and volume and switch
  • Output – audio connector 3.5 mm
  • Board Dimensions – 100 x 59 mm
  • Design – without box
  • Package Contents – printed circuit board, RDA5807M module, 3.3 V power module, microcontroller with socket, LED display, speaker, telescopic antenna, USB-C cable, holder for 2 AA batteries, resistors, capacitors, transistors, buttons, 3.5 mm connector, trimmer and jumper wires

Before soldering, check against the parts list to ensure the kit contains all parts. First, solder the lower components and modules, then the higher parts, and finally solder the wires to the speaker and battery holder. Attach the antenna base with a screw and solder it from the back of the board. When working, use a soldering iron with an appropriate tip and pay attention to the correct orientation of polarized components such as capacitors, transistors, and the display.

This soldering kit is suitable for students, beginner electronics enthusiasts, and more experienced hobbyists who want to practice soldering on a meaningful project. The result is a functional FM receiver with a telescopic antenna of 30 cm and stable power supply. Thanks to the power supply from USB-C or batteries, the finished radio can be easily used at home, at school, or in the workshop. Assembly teaches reading schematics, populating the board, and working with modules. The kit is suitable for electronics clubs, technology classes, and as a gift for electronics enthusiasts.

Price incl. VAT €37.07