Home page Home page Auto & Moto Car bulbs LED headlight bulbs LED H1 Bulbs 2 Pieces 5570 CSP Chips 3.5 x 7.5 x 1.4 cm Black Body with Fins and Light Beam White Light 6000 K For Car Headlights
LED H1 Bulbs 2 Pieces 5570 CSP Chips 3.5 x 7.5 x 1.4 cm Black Body with Fins and Light Beam White Light 6000 K For Car Headlights

LED H1 Bulbs 2 Pieces 5570 CSP Chips 3.5 x 7.5 x 1.4 cm Black Body with Fins and Light Beam White Light 6000 K For Car Headlights

Looking for an LED replacement for H1 halogen bulbs? This set of 2 pieces with 5570 CSP chips emits white light at 6000 K and each bulb measures 3.5 x 7.5 x 1.4 cm. Full description
In stock
€36.64
Safe shopping Safe shopping
Overview
LED H1 Bulbs 2 Pieces 5570 CSP Chips 3.5 x 7.5 x 1.4 cm Black Body with Fins and Light Beam White Light 6000 K For Car Headlights

Instead of halogen H1 bulbs, you can install these two LED bulbs with a H1 base in your car. The light source of each bulb is a block of 5570 CSP chips, which emit white light at 6000 K. The chips are mounted on a light flat beam with a black design. The lower half of the bulb consists of a black heatsink with fins, and above it is a red ring. Each bulb occupies a space of 3.5 x 7.5 x 1.4 cm.

  • Typical H1 Use — H1 bulbs are typically installed in high beams or fog lights, but this can vary by vehicle. The crucial factor is the marking on the bulb you are replacing.
  • Chip Block — the 5570 CSP chips form a yellow rectangle on the beam, surrounded on both sides by black graphic stripes. The chip area is divided into several smaller segments.
  • Light Colour — at a colour temperature of 6000 K, the light has a pure white tone without any yellow component. This is the main difference you will notice after replacing the halogen H1 bulbs.
  • Black Body — the body of the bulb below the beam is black and transitions into a heatsink, whose fins run the full height of the lower part. The surface of the fins serves to cool the LED chips. Above the heatsink, there is a red ring on each bulb.
  • Bulb Size — with dimensions of 3.5 x 7.5 x 1.4 cm, the LED bulb is bulkier than a standard halogen H1 due to the heatsink. Before purchasing, check that there is enough space behind the light for the cover.
  • Vehicle Compatibility — the H1 type is usually stamped on the metal part of the original bulb or listed in the vehicle's manual. If you are unsure of the type, compare the original bulb with a parts catalogue for your model.
  • Both Lights Even — by replacing both pieces, you ensure that the lights on the left and right sides will not have differing shades.
  • How to Proceed — the halogen bulb gets very hot while lit, so remove it only after it has cooled down. Then insert the H1 LED bulb and secure it as the original bulb was held.
  • Post-Installation Verification — turn on the lights and check that both LED bulbs are illuminated. If the height of the light boundary has changed after replacement, it is advisable to have the lights adjusted at a service centre.
  • Road Use and LED — before installation in halogen lights, check what regulations apply to LED bulbs in your country and for your type of lights.

Package Contents:

  • 2x H1 LED Car Bulb with Chips

The package with 2 pieces of H1 LED bulbs covers both lights of the vehicle. Thanks to the 5570 CSP chips, the bulbs emit white light at 6000 K. Both bulbs have a black body with a heatsink and a red ring above the fins. Before purchasing, verify the H1 type on the original bulb and the space for the heatsink behind the light. This set is suitable for car owners with H1 bulbs who wish to switch from halogen to LED.

Price incl. VAT €36.64