LUNZO s.r.o. (Czechia) · info@lunzo.ie · +420 603 337 330 · Mon–Sun 8:00–17:00 Irish time · Contact Us

Home page Home page Hobbies & Garden Measuring Instruments Protractors Digital Laser Level with Magnets on Four Sides, Range 4 x 90°, Resolution 0.05° and Accuracy 0.2° with USB-C Charging
Digital Laser Level with Magnets on Four Sides, Range 4 x 90°, Resolution 0.05° and Accuracy 0.2° with USB-C Charging

Digital Laser Level with Magnets on Four Sides, Range 4 x 90°, Resolution 0.05° and Accuracy 0.2° with USB-C Charging

Beams from both sides mark the plane on the wall and the magnets hold the device in any position. The display shows degrees and percentages and charges via USB-C cable. Full description
In stock
Colour:
€62.40
Safe shopping Safe shopping
Overview
Digital Laser Level with Magnets on Four Sides, Range 4 x 90°, Resolution 0.05° and Accuracy 0.2° with USB-C Charging

The measuring device combines a digital inclinometer with a laser, as red beams project from both sides, marking the measured plane directly on the wall or floor. The measurement range covers 4 x 90°, the display step is 0.05° and the stated accuracy is ±0.2°, making it suitable for finer adjustments and for checking completed work. Magnets are built into all four walls, allowing the device to attach to a saw blade, vertical profile, or the underside of a steel frame without clamps and without assistance. Control consists of three buttons, which turn the device and laser on, hold the value on the display, and set zero on the chosen surface for measurement against its own reference. Power is provided by a built-in 3.7 V lithium battery, which charges via a USB-C connector, and the package includes a cable and a fabric case.

  • Display step 0.05° – the value changes in increments of five hundredths of a degree, allowing for slow fine-tuning of the slope during machine or stop adjustments.
  • Measurement tolerance ±0.2° – the stated deviation corresponds to assembly work, furniture manufacturing, and checking the slope of structures on site.
  • Repeatability 0.1° – repeated placement at the same point yields a value within one tenth of a degree, which aids in comparing two surfaces and checking a series of parts.
  • Laser on both sides – beams project opposite each other, extending the tool's plane on both sides, so the line projects across the entire width of the room from a single position.
  • Four magnetic sides – the device can attach to any wall, allowing measurements even when placed on its side or underneath, where hand access may be limited.
  • Measurement across four quadrants – the range of 4 x 90° covers the entire circumference, allowing the device to be placed flat, upright, or upside down.
  • Switch to slope percentage – in addition to the angle in degrees, the value is displayed as a percentage of incline, which is useful for pipes, gutters, and ramp surfaces.
  • Value lock – the hold button freezes the displayed value, allowing the device to be removed from a position out of sight, with the number read later.
  • 3.7 V lithium battery – the rechargeable cell is topped up with a USB-C connector cable, eliminating the need to purchase disposable batteries.
  • Operating temperature from -10 °C to 50 °C – the stated temperature range covers heated workshops, unheated garages, and outdoor work on non-freezing days.

Package contents:

  • 1x digital level
  • 1x charging cable
  • 1x case

The level is useful for adjusting saws and mills, assembling furniture and railings, measuring partitions, and checking the slope of pipes. Before measuring, it is advisable to place the device on a flat surface and set zero, as absolute measurements are based on the horizontal plane. The magnetic walls should be wiped clean of metal dust, as even a small chip can lift the body and alter the measured angle. The laser must not be aimed at eyes, so the device should be rotated so that the line ends on the working surface and does not extend into a passage area. After use, the device should be wiped clean, stored in the case, and charged as needed to be ready for the next measurement.

Price incl. VAT €62.40